-
Xuntong specializes in testing services for electrical accessories, consumer electronics, lighting, wireless, toys and other products.
Service Hotline 18617145297
|
CE |
ECE R10 |
Unform provisions concerning the approval of vehicles with regard to electromagnetic compatibility. |
|
CISPR |
CISPR 25 |
Vehicles, boats and internal combustion engines – Radio disturbance characteristics – Limits and methods of measurement for the protection of on-board receivers |
|
EN |
EN 13309 |
Construction machinery – Electromagnetic compatibility of machines with internal power supply |
|
EN |
EN 50498 |
Electromagnetic compatibility (EMC) – Product family standard for aftermarket electronic equipment in vehicles |
|
EN |
EN 55025 |
Vehicles, boats and internal combustion engines. Radio disturbance characteristics. Limits and methods of measurement for the protection of on-board receivers |
|
ISO |
ISO 10605 |
Road vehicles – Test methods for electrical disturbances from electrostatic discharge |
|
ISO |
ISO 11452-1 |
Road vehicles – Component test methods for electrical disturbances from narrowband radiated electromagnetic energy – Part 1: General principles and terminology |
|
ISO |
ISO 11452-2 |
Road vehicles – Component test methods for electrical disturbances from narrowband radiated electromagnetic energy – Part 2: Absorber-lined shielded enclosure |
|
ISO |
ISO 11452-3 |
Road vehicles – Component test methods for electrical disturbances from narrowband radiated electromagnetic energy – Part 3: Transverse electromagnetic mode (TEM) cell |
|
ISO |
ISO 11452-4 |
Road vehicles – Component test methods for electrical disturbances from narrowband radiated electromagnetic energy – Part 4: Bulk current injection (BCI) |
|
ISO |
ISO 11452-5 |
Road vehicles – Component test methods for electrical disturbances from narrowband radiated electromagnetic energy – Part 5: Stripline |
|
ISO |
ISO 11452-7 |
Road vehicles – Component test methods for electrical disturbances from narrowband radiated electromagnetic energy – Part 7: Direct radio frequency (RF) power injection |
|
ISO |
ISO 11452-8 |
Road vehicles – Component test methods for electrical disturbances from narrowband radiated electromagnetic energy – Part 8: Immunity to magnetic fields |
|
ISO |
ISO 11452-9 |
Road vehicles – Component test methods for electrical disturbances from narrowband radiated electromagnetic energy – Part 9: Portable transmitters |
|
ISO |
ISO 11452-10 |
Road vehicles – Component test methods for electrical disturbances from narrowband radiated electromagnetic energy – Part 10: Immunity to conducted disturbances in the extended audio frequency range |
|
ISO |
ISO 12097-3 |
Road Vehicles – Airbag Components – Part 3: Testing of Inflator Assemblies |
|
ISO |
ISO 13766 |
Earth-moving machinery Electromagnetic compatibility |
|
ISO |
ISO 16750-2 |
Road vehicles. Environmental conditions and testing for electrical and electronic equipment. Electrical loads |
|
ISO |
ISO 17025 |
General requirements for the competence of testing and calibration laboratories |
|
ISO |
ISO 7637-1 |
Road vehicles – Electrical disturbances from conduction and coupling – Part 1: Definitions and general considerations |
|
ISO |
ISO 7637-1-2 |
|
|
ISO |
ISO 7637-2 |
Road vehicles – Electrical disturbances from conduction and coupling – Part 2: Electrical transient conduction along supply lines only |
|
ISO |
ISO 7637-3 |
Road vehicles – Electrical disturbances from conduction and coupling – Part 3: Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines |
|
SAE |
J1113-3 |
Conducted Immunity, 250 kHz to 400 MHz, Direct Injection of Radio Frequency (RF) Power |
|
SAE |
J1113-4 |
IMMUNITY TO RADIATED ELECTROMAGNETIC FIELDS.BULK CURRENT INJECTION (BCI) METHOD |
|
SAE |
J1113-11 |
Immunity to Conducted Transients on Power Leads |
|
SAE |
J1113-12 |
Electrical Interference by Conduction and CouplingCapacitive and Inductive Coupling via Lines Other than Supply Lines |
|
SAE |
J1113-13 |
Electromagnetic Compatibility Measurement Procedure for Vehicle ComponentsPart 13: Immunity to Electrostatic Discharge |
|
SAE |
J1113-21 |
Electronmagnetic Compatibility Measurement Procedure for Vehicle Components – Part 21: Immunity to Electromagnetic Fields, 30 MHz to 18 GHz, Absorber-Lined Chamber |
|
SAE |
J1113-22 |
Electromagnetic Compatibility Measurement Procedure for Vehicle Components-Part 22-Immunity to Radiated Magnetic Fields |
|
SAE |
J1113-23 |
Electromagnetic Compatibility Measurement Procedure for Vehicle Components – Immunity to Radiated Electromagnetic Fields, 10 kHz to 200 MHz, Strip Line Method, Recommended Practice |
|
SAE |
J1113-24 |
Immunity to Radiated Electromagnetic Fields; 10 kHz to 200 MHz-Crawford TEM Cell and 10 kHz to 5 GHz-Wideband TEM Cell |
|
SAE |
J1113-41 |
Limits and Methods of Measurement of Radio Disturbance Characteristics of Components and Modules for the Protection of Receivers Used on Board Vehicles |
|
SAE |
J1113-42 |
Electromagnetic Compatibility-Component Test Procedure-Part 42-Conducted Transient Emissions |
|
ECE R10 |
CISPR 25 |
EN 13309 |
EN 50498 |
|
EN 55025 |
ISO 10605 |
ISO 11452-1 |
ISO 11452-2 |
|
ISO 11452-3 |
ISO 11452-4 |
ISO 11452-5 |
ISO 11452-7 |
|
ISO 11452-8 |
ISO 11452-9 |
ISO 11452-10 |
ISO 12097-3 |
|
ISO 13766 |
ISO 16750-2 |
ISO 17025 |
ISO 7637-1 |
|
ISO 7637-1-2 |
ISO 7637-2 |
ISO 7637-3 |
J1113-3 |
|
J1113-4 |
J1113-11 |
J1113-12 |
J1113-13 |
|
J1113-21 |
J1113-22 |
J1113-23 |
J1113-24 |
|
J1113-41 |
J1113-42 |
professional equipment
WeChat Consultation
Submission Successful
WeChat Official Account